-
Reasons for uneven color of the oxide film of aluminum material
Three possible causes of aluminum profile oxide film color is not uniform: (1)When anodized the aluminium profiloe the workpiece area is too large, the swing range in the slot is too large, the edge and the center position and solution contact, update, exchange had large differences, resulting i...Read more -
Aluminum profile production process quality control techniques
Aluminum profile production process consists of aluminum ingot casting, and then extruded aluminum billets, and then through the surface treatment, such as: Anodizing, sandblasting and so on, in the specific operation process each process is very important, here we points out some aspects of spec...Read more -
How to do the spray cleaning of industrial aluminum profile？
spray cleaning of industrial aluminum profile is widely used, because of complicated equipment, high technical requirements, the cleaning effect is not good, so how to do the cleaning of industrial aluminum profile: 1, Strengthen technological and the implementation of strict operation rules. Ev...Read more -
The advantages of broken bridge aluminum window and door
Broken bridge aluminum doors Broken bridge aluminum windows Broken bridge aluminum window and door with many advantages, mainly include: reduce the heat-conduction: if adopts the heat insulation break bridge aluminum alloy profiles, the heat transfer coefficient is lower ...Read more -
Aluminum alloy decoration
The aluminum alloy trim panel has the advantages of light, not burning, durability, convenient construction, good decoration, etc., which is suitable for the decoration of the internal and external walls and cylinders of the public building. In recent years, there are several kinds of aluminum a...Read more -
Why use ultrafiltration system in electrophoretic coating process ？
Ultrafiltration system of Electrophoresis coating process of the main purpose is to enable the E COAT aluminium is a closed-loop system, reducing emissions of pollutants, and can also save the electrophoresis coating material. The workpiece after electrophoresis with very low electrical conduct...Read more -
Good aluminium tube identification tips
Chinese aluminum tube market prospect is very wide, it also brings bad atmosphere to the entire market, in order to avoid consumer loss, today we taught you a simple four words identification of official tubes and the defective. I. by look and touch The surface of aluminum tube were identified t...Read more -
Aluminum shutter process technology
Aluminum shutter process technology 1. Leaf blade uses the high quality aluminum alloy materials and processing, with double-sided enamel paint, matched with the fittings and accessories. 2. Up and down track is made of aluminum pressing molding one, coating with 3. Iron head tank, bottom tank ...Read more -
Which is better ? aluminium casement window or sliding window
According to the opening mode, Aluminum alloy doors and windows could be classification two popular kinds: Casement window and sliding window. aluminium casement window aluminium sliding window Casement window hinge is installed on the door side inward or outward opening doors and ...Read more -
Development trend of high strength aluminum alloy
Development trend of high strength aluminum alloy High strength aluminum alloy is an important lightweight high-strength structural material, which has broad application prospects. The application of aluminum and aluminum alloy is challenged by titanium and titanium alloy and composite materials...Read more -
How to improve the strength of the aluminum profile?
The strengthening of aluminum alloy is mainly to increase its resistance to dislocation action, so there are two ways to strengthen aluminum alloy: liquid treatment and solid state treatment. Liquid treatment is the strengthening of dispersion distribution of carbide, boride and nitride in alum...Read more -
Some reasons for the uneven color of the oxide film of aluminum material
Three possible causes of aluminum profile oxide film color is not uniform: (1) when anodized the aluminium profiloe the workpiece area is too large, the swing range in the slot is too large, the edge and the center position and solution contact, update, exchange had large differences, resulting...Read more -
Difference of steel, copper and aluminum radiator
Copper and aluminum radiator composite takes advantage of the aluminium heat fast , and the corrosion resistance of copper to increase the service life of the radiator, detail good feature of cooper and aluminium radiator as follows: 1、cooper and aluminium radiator with rich colors and...Read more -
Attentions when extrusion of 6082 aluminium alloy profiles
(1), aluminum alloy ingot heating A, The line frequency induction heating of aluminum alloy ingot heating, the heat mode with feature as follows. B, extrusion temperature control is accurate, the error is less than ± 3 ℃. If the resistance furnace is heated slowly, will cause the Mg2Si phase pre...Read more -
Powder spraying process on the surface of aluminum alloy
Powder spraying is used to spray powder coating on the surface of the workpiece by spraying powder equipment (electrostatic spray plastic machine). In electrostatic action, the powder will be evenly adsorbed on the surface of the workpiece to form a powdery coating; the powder coating is solidif...Read more -
Classification of main products of aluminum alloy
Aluminum alloy is one of the most widely used nonferrous metal structural materials in industry. It has been widely used in aviation, aerospace, automobile, mechanical manufacturing, shipbuilding and chemical industry. The main products of aluminum alloy are classified as follows: 1. aluminum al...Read more -
Problems and solutions in injection molding process
Injection molding is a method of industrial product modeling. The products are usually made of rubber injection and plastic injection. Injection molding can also be divided into injection molding and die casting. Shrinkage, shrinkage, non full mold, wool edge, weld mark, silver wire, spray mark,...Read more -
Plastic moulds – blow molding
Extrusion blow molding is a method of manufacturing hollow thermoplastic parts. The well known blow objects include bottles, barrels, cans, boxes and containers for all packaged foods, beverages, cosmetics, medicines and daily necessities. Large blow molding containers are usually used for packa...Read more -
Welding method of aluminum and aluminum alloy
Almost all kinds of welding methods can be used to weld aluminum and aluminum alloys, but the adaptability of aluminum and aluminum alloy to various welding methods is different. All kinds of welding methods have their respective applications, and the following are the more common methods of wel...Read more -
The function and basic principle of chemical polishing on aluminum alloy surface
The aluminum alloy workpiece after mechanical polishing has obtained bright surface, but if the workpiece after mechanical polishing is anodized directly, it is only a smooth surface and can not get the film with high reflective coefficient, so the workpiece after mechanically polished must be c...Read more -
The function and mode of aluminum alloy connector
Aluminum alloy section connector relates to aluminum alloy profile. A right angle piece, a slot T bolt, an elliptical shim and a nut are arranged on both sides of the right angle piece, and there are two orthogonal elliptical holes on the right angle part, one of which is an elliptical hole for ...Read more -
The bolt is actually a large family. What is a T bolt?
The T bolt is literally understood to be that the shape of the bolt is like a capitalized English letter “T”, which has its reputation. Some T bolts are also called T screw or T type screw. The aluminum alloy profiles are T type bolts and hammerhead bolts. The materials are SUS304 st...Read more -
Numerical control laser cutting machine
The machine has the characteristics of cutting speed, small cutting in the cutting process of CNC cutting. The design of industrial machine machine tool ensures high speed and stability of laser cutting process, and selects fiber laser with different power. It can cut and punch all kinds ...Read more -
Rapid prototyping
apid prototyping technology, also called rapid prototyping, (RP Technology); English: RAPID PROTOTYPING (referred to as RP),or RAPID PROTOTYPING MANUFACTURING, or RPM. In the automotive industry, the RP sample is called. RP technology is integrated and developed on the basis of modern CAD/CAM te...Read more